Cleaning Engine Intake with Seafoam: Before & After

#ad: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases.

Sea Foam Spray engine cleaner

My old Jaguar runs, but not great, so I tried a can of Sea Foam Spray to clean out the intake.

My 40-plus-year-old Jaguar XJ6 hesitates on cold starts, runs a little rich, and sometimes needs gas to keep going. Sea Foam Spray Top Engine Cleaner and Lube comes with a snake straw that you aim into the intake while the engine runs. A can is not expensive, so I followed the directions to the letter to see if it would help.

Sea Foam Spray Top Engine Cleaner & Lube (SS12)
Featured in this video
Sea Foam Spray Top Engine Cleaner & Lube (SS12)
Check Sea Foam Spray on Amazon →
#ad, affiliate link
Quick specs (from the video)
ProductSea Foam Spray Top Engine Cleaner & Lube (SS12)
ProductSea Foam Spray top engine cleaner & lube
ApplicatorBendable straw sprayed into the intake toward the throttle body
Spray timeAbout 5 to 6 minutes to run the whole can
Heat soak10 minutes with the engine off
Drive afterAt least 10 minutes of spirited driving
Car1970s Jaguar XJ6
👍 Pros
  • Inexpensive and easy to do yourself
  • Visible results: white smoke and ash pushed out the exhaust
  • Idle was far smoother after driving
👎 Cons
  • It helps to have a second person, one to spray and one to hold the revs
  • It smokes and does not smell great, so do it outside
  • The car idled rough for a while before it improved

▶ Watch the full review on YouTube

Step 1: warm the engine

The directions say to bring the engine up to temperature first. Mine fired up rough, hesitating and bouncing, so I let it run a few minutes to warm up.

Sea Foam Spray engine cleaner
Sea Foam Spray engine cleaner from my video.

Step 2: spray into the intake

On my car the air filter and mass airflow sensor feed a tube to the throttle body. I loosened the clamp, pulled the boot, fed the Sea Foam straw in with its bend aimed at the throttle body, and put the hose back on. The butterfly valve did not look that bad.

I did not have a helper, so I sprayed with one hand and kept the revs up with the other. Running the whole can through took about five or six minutes. A decent amount of white smoke came out of the exhaust, which I took as a good sign of carbon burning off.

Sea Foam Spray engine cleaner detail
A closer look at the Sea Foam Spray engine cleaner.

Step 3: heat soak and drive

Next the engine sits for 10 minutes to heat soak. When I restarted it, both exhausts spat out black stuff onto the driveway that looked like ash and carbon. Better out of the car than in, and the first time I have seen that happen.

Then you drive at least 10 minutes in a spirited fashion. In a 1970s XJ6 that is pretty underwhelming, but at least the engine is under load.

Sea Foam Spray engine cleaner in use
The Sea Foam Spray engine cleaner in use.

Results

At first I was worried. It idled pretty rough at stop lights. After driving about 25 to 30 minutes in total with errands, it was much better: driving felt fine, and the idle was maybe only 10% as rough as when I started. For the price of a can, that is worth trying.

FAQ

How long does it take to spray a can of Sea Foam?

It took me about five or six minutes, depending on how long you can hold the nozzle down.

Is white smoke normal after using Sea Foam?

I got a decent amount of white smoke out of the exhaust, and black ash spat out on the next start, which I took as carbon being cleared.

Do I need to drive after the treatment?

Yes. The directions call for a 10-minute heat soak and then at least 10 minutes of spirited driving.

Is this an affiliate link?

Yes. The buttons are #ad affiliate links, and as an Amazon Associate I earn from qualifying purchases. It costs you nothing extra.

Sea Foam Spray Top Engine Cleaner & Lube (SS12)
Ready to grab one?
Sea Foam Spray Top Engine Cleaner & Lube (SS12)
Check Sea Foam Spray on Amazon →
#ad: As an Amazon Associate I earn from qualifying purchases.

Leave a Reply